Your position: Home
>
Happy Model - Crux3 Brushless Toothpick class FPV Drone
Happy Model - Crux3 Brushless Toothpick class FPV Drone
No.
HP037-0152
| Item Name | Qty |
| Crux3 Frame and canopy | 1 |
| Option1: CrazybeeX FR V2.2 built-in internal Frsky SPI D8/D16 receiver | 1 |
| Option2: CrazybeeX FS V2.2 built-in internal Flysky SPI receiver | |
| Option3:CrazybeeX DXS V1.0 built-in internal DSM2/DSMX SPI receiver | |
| Option4:CrazybeeX PNP V2.2 with External Frsky RXSR receiver | |
| Option5:CrazybeeX PNP V2.2 with External TBS crossfire nano receiver | |
| Happymodel EX1202.5 KV6400 brushless motor | 4 |
| Gemfan 3018 bi-blade Propellers(4cw+4ccw) | 1 |
| Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera | 1 |
| 5.8G 25mw~200mw 40ch vtx (Flight controller built-in) | 1 |
| Screw Driver | 1 |
| Propeller disassemble tool | 1 |
| Happymodel Handbag | 1 |
| Motor | Mode: EX1202.5 KV6400 Configu-ration:9N12P Stator Diamter:12mm Stator Length:2.5mm Shaft Diameter:Φ1.5mm Motor Dimension(Dia.*Len):Φ14mm*14.5mm Weight(g):4.4g No.of Cells(Lipo):1-2S |
| Propellers | Gemfan 3018-2 Center Thickness:5.5mm Prop Diameter:76.5mm Center Hole diameter:1.5mm |
| Flight controller | (Frsky SPI RX version) CRAZYBEEX FR V2.2 FC Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEEX FS V2.2 FC Firmware target: CrazybeeF4FS (DSM2/X SPI RX version)CRAZYBEEX DXS V1.0 FC firmware target:CrazybeeF4DXS (External Frsky RXSR version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DX (External TBS CRSF NANO version) CRAZYBEEX PNP V2.2 Firmware target:CrazybeeF4DX MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver or no receiver Built-in 5V 1A BEC |
| Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600 |
| Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
| Onboard Flysky SPI receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
| Onboard DSM2/X SPI receiver Version | SPI BUS receiver DSM2/DSMX compatible Channels: Max 12ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m RSSI enable(show on the goggles) |
| External Frsky R-XSR receiver version | Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware) |
| External TBS CRSF Nano receiver version | Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible |
| Onboard 5.8g VTX | Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready |
| Caddx ANT 1200tvl camera | Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 16:9 or 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm Min. Illumination: [email protected] Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.) |
