PRODUCT DESCRIPTION
The SucceX-D F7 V2.1 TwinG // GYRO FUSION is the NEXT-GEN flight controller you need for your build. This FC is ready for anything with 5 uarts, 8 motor outputs, 32Mb blackbox and a powerful F7 processor to run it all. Designed to work seamlessly with DJI’s new HD FPV system. To make things even simpler, the DJI Air unit can just be plugged into the FC with the included wire harness. In addition, we added the popular and reliable USB Type-C instead of Micro USB and therefore the same standard than your DJI module.
Top Features:
• DJI Plug-and-Play - No need to solder tiny wires!
• Gyro Fusion - Zero delay Twin-Gyro filtering!
• Dual BEC 5V and 9V
FC // SucceX-D F7 TwinG
MCU: 216MHz STM32F722
Gyro：2x ICM20689
Baro: YES
Blackbox：32MB
Betaflight OSD: YES
BEC: 5V 2.5A / 9V 2.5A
Current sensor scale: 100
Inverter for SBUS input (UART2-RX)
Smartaudio & Tramp VTX protocol supported
Beeper pad : Yes
RSSI input pad: No
UARTs：5
Motor outputs: 8
8 pin 4in1 ESC port (GND, VBAT, M1, M2, M3, M4, CUR, R5)
6 pin DJI Air Unit port (R1, GND, R2, T2, GND, 9V)
BLHeli32 Telemetry：RX5
Input voltage：recommended 2-6S, MAX 8S
Firmware: IFLIGHT_F722_TWING
Mounting pattern: 30.5*30.5mm φ4mm with Grommets φ3mm
Dimensions: 36*36mm
Weight: 7.5g
USB type-C
ESC // SucceX 50A 2-6S 4in1
Top Features:
- 8 layers double-sided PCB board
- 3oz 1.4mm thick power board
- 32bit STM32F051 MCU, 48kHz maximum clock speed
- TDK MLCC Low ESR ceramic capacitors
- Top grade NTMFS5C430NL MOSFET
Specification:
MCU: STM32F051
Up tp 48kHz PWM frequency
Capacitance: 470uF/50V
Current Sensor: Yes
Input: 2-6S LIPO
Constant: 35A / Burst: 40A
BlHeli32 telemetry: Yes
BEC: No
Supports up to Dshot1200, Proshot, Oneshot, Multishot
Target: iFlight-BL32-4IN1
Weight:14.4g
Mounting pattern: 30.5*30.5mm/Φ3mm
Dimensions: 43*39mm (including the power pads)
DJI Digital HD FPV Air Unit
Digital HD systems have traditionally been rather bulky and unwieldy to mount on a mini quad. Not anymore. With this air unit, you can comfortably fit the module in your mini quad stack (probably not slammed frames). The 'mini' camera fits easily into your existing builds, no weird mounting adapters.
Note: The Air Unit module does get very hot in use. Do not power on for an extended period of time without proper cooling.
Specifications
Weight：Air Unit (Camera included): 45.8 g，3.9 g (MMCX each)
Air Unit: 44 × 37.8 × 14.4 mm
Camera: 27.4 × 21.1 × 20.1 mm
Operating Frequency: 5.725-5.850 GHz
Transmitter Power (EIRP): FCC/SRRC: <30 dBm; CE: <14 dBm
Low Latency Mode (720p/120fps): <28 ms
High-Quality Mode (720p/60fps): <40 ms
Max. Transmission Distance: FCC/SRRC: <4 km; CE: <0.7 km
Video Format: MP4 (Video format: H.264; Audio format: ACC-LC)
I/O Interface: USB-C, MMCX, 3-in-1 port, microSD card slot
Input Power: 7.4-17.6 V, about 4-9 W
Lens: 2.1 mm, f/2.1
FOV: 150°(D); 122°(H); 93°(V)
Weight: 8.2 g
Package Includes：
- SucceX-D F7 TwinG Flight Controller × 1
- SucceX 50A 4-in-1 ESC × 1
- DJI FPV Air Unit (with a camera and four M2 screws) × 1
- Three-in-one cable × 1
- Antenna (MMCX) × 2
