Happy Model - Moblite6 ultra light 1S 65mm brushless whoop
No.
HP037-0153
Item Name | Qty |
65mm Frame (Mobula6 frame) | 1 |
Option1: DiamondF4 FR built-in SPI Frsky receiver | 1 |
Option2: DiamondF4 FS built-in SPI Flysky receiver | |
EX0802 KV19000 Unibell brushless motor | 4 |
Gemfan 1219 31mm propeller(4cw+4ccw) | 1 |
Runcam Nano4 Lite | 1 |
Built-in 5.8G 40ch 25mw-200mw VTX | 1 |
1s 300mah Lipo battery | 2 |
1S USB charger | 1 |
Propeller disassemble tool | 1 |
Screwdriver | 1 |
Happymodel Carry case | 1 |
Motor | Mode: EX0802 19000KV Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm Weight(g):1.7g No.of Cells(Lipo):1S only |
Flight controller | (Frsky SPI RX version) DiamondF4 FR FC Firmware target: CrazybeeF4FR (Flysky SPI RX version)DiamondF4 FS FC Firmware target: CrazybeeF4FS MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Original whoop size compatible Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BEC |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_50_REV16_8.HEX Default protocol: DSHOT600 |
Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 model Channels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m |
Onboard Flysky SPI receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support |
Onboard 5.8g VTX | Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels(include Race band) Smartaudio ready |
Runcam Nano4 Lite | Model: RunCam Nano4 Lite Image Sensor: 1/3" CMOS Horizontal Resolution: 800TVL Lens : 2.1mm(M8) FOV 160° Signal System: PAL/NTSC Non Switchable S/N Ratio: >50dB Electronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: [email protected] D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 170mA@5V [email protected] Housing Material: ABS Net Weight: 1.0g Dimensions: L14mm*W12mm*H9mm |
Lipo Battery | Capacity:300mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 57mmx12mmx7mm Weight: 7.5g Connector: PH2.0 |